Paid plugin · Four-band equalizer · Windows & macOS · 14-day trial

Ferrule 81

Ferrule 81 is a four-band equalizer with a switched high-pass and low-pass filter. The high and low bands each switch between shelf and bell, the two mid bands each have a HI Q mode, and every mode of every position is a separately measured curve. It runs as a mono or stereo plug-in (Stereo, Dual Mono, M/S) with a 14-day full trial and an offline licence.

How the trial works

Ferrule 81 -- the module
At a glance

The facts, in numbers

Bands4 (HF, HI-MID, LO-MID, LF), +/-15 dB, plus a 6-position HPF and a 6-position LPF
Opens flatEvery frequency selector defaults to OFF, so a fresh instance opens flat apart from the always-on stage; a band or filter set to OFF is out of the path
Always-on responseWith EQ IN on and every band at 0 dB: a fixed response of up to about 0.79 dB (0.21 dB rms), rising toward the top of the band. EQ IN out is bit-transparent
OversamplingOff / 2x / 4x / 8x; default Off. There is no level-dependent stage, so it does not change the EQ curve
Latency0 samples at the default; 3 / 4 / 5 at 2x / 4x / 8x
Presets34 factory presets. Init plus 33 starting points: vocals, drums, bass, guitar, keys, buses and utility.
StereoMono or stereo instance; Stereo (linked), Dual Mono, M/S
Sample rates44.1-384 kHz, designed coefficients at each of eight rates, so the response in Hz is the same at every one
DCBlocked inside EQ IN (first-order, 2 Hz; -0.04 dB at 20 Hz; DC down by more than 138 dB). With EQ IN out, DC passes
BypassClick-free: the power switch crossfades over about 15 ms, with the dry path delay-matched
Controls

Every control on the strip

Every frequency control is a switch, so every position you can select is a position that was measured. Ctrl / Cmd while dragging moves a gain knob in exact 0.1 dB steps.

EQ INPuts the equalizer in and out per strip. Out is bit-transparent.
HF+/-15 dB. OFF, 3.3k, 4.7k, 6.8k, 10k, 15k. PEAK button: shelf or bell.
HI-MID+/-15 dB. OFF plus ten frequencies from 1.5k to 8.2k Hz. HI-Q 2 button.
LO-MID+/-15 dB. OFF plus ten frequencies from 220 Hz to 1.2k. HI Q button.
LF+/-15 dB. OFF, 33, 56, 100, 180, 330 Hz. PEAK button: shelf or bell. A resonant shelf.
HPF / LPFHPF: OFF, 27, 47, 82, 150, 270 Hz. LPF: OFF, 18k, 12k, 8.2k, 5.6k, 3.9k Hz. One knob.
General sectionAnalyzer screen (Curve, FFT, Phase), IN / OUT meters and trims, stereo-mode selector, power switch. UI size 75-200%
Try before you buy

14 days, every feature

The free trial is on the Ferrule 81 Gumroad page: the button below opens it; press Start the free 14-day trial there (price 0) for the Ferrule 81 installers for Windows and macOS. Install, insert Ferrule 81 in your host and press Start Free Trial inside the plug-in: 14 days, full features, full audio quality, no watermark. The clock starts when you press Start Free Trial, not when you download. Each Ferrule product has its own 14 days. When you buy, the same installation unlocks -- nothing to reinstall. Gumroad may ask for an email address to deliver the files.

We do not offer refunds on paid purchases -- the trial is how you decide. Your statutory rights are not affected. Refund policy

Known limits

What is not perfect, plainly

We ship disclosure, not marketing. These are the known limits of Ferrule 81 1.0.0; the manual carries the full list, and the Ferrule FAQ answers the common questions.

  • The reported latency is nominal (manual section 9.1): with oversampling on, the measured group delay runs up to about 0.7 samples longer than the reported figure; with oversampling Off the reported 0 matches the measurement at 44.1, 48 and 96 kHz.
  • Unlicensed and offline renders. Without a trial or license the plug-in passes audio dry, including during an offline render (manual section 12).
  • Already-open instances do not re-read a license you add while they are loaded (manual section 12).
  • Group delay of the oversampling filters is not constant (manual section 9.2).
  • Sample rates other than 44.1, 48, 88.2, 96, 176.4, 192, 352.8 and 384 kHz -- no host offers one -- are answered with the nearest designed set, which is an approximation and not a designed response.
  • Not measured for this manual: playback in every host on every platform. The primary verification host is Studio One, and Logic on macOS. Every figure here is a reading of the Windows build; none was measured on macOS. Pro Tools (AAX): when this manual was written the AAX build had not yet been tried by hand in Pro Tools itself; the release procedure runs Avid's AAX validator on the signed build before it is published.
  • Dial ladders (current table). Counted over the 301 dial positions of every setting at all eight rates, a fall of more than 0.02 dB between two adjacent positions is one step. At 44.1 and 48 kHz there are none. Across all eight rates there is 1 step in 1 of 480 setting-and-rate rows, in the HF 10k shelf at 192 kHz at dial +0.6 dB (0.05 dB); at the other seven rates none. The engine read behind Appendix A agrees at 48 kHz: one 0.1 dB step (HI-MID 6.8k bell, HI-Q 2, dial +2.9 to +3.0 dB) moves the reading backwards, by 0.01 dB. Positions between the dial values printed in Appendix A are not tabulated there.
  • Between measured dial values the response is interpolated and is not itself compared with a measurement.
  • Always-on stage. EQ IN on at 0 dB is not bit-identical to the input (manual section 2).
  • Phase and delay of the analysed unit are not reproduced (manual section 11).
  • A preset load is one step. A factory preset, a user preset, Reset to Init and a restored session each write every parameter they set once, straight to its final value, and the audio engine takes the whole set up at a single buffer boundary, so no buffer plays a half-loaded mix of the old and new settings. Host automation that arrives while a load is being applied is taken up as soon as the load ends (a few milliseconds).
  • The level just after a preset load. In a test with steady tones (every factory preset loaded over Init and over its neighbours in the list, both directions) no load rose more than 0.02 dB above the settled level.
  • A switch that changes the latency (the oversampling mode or phase and, where this product has them, the Bloom engine, Flutter or Look) fades the output out over 5 ms, holds silence and fades it back in over 5 ms. For an oversampling change the whole mute lasts about 21 ms into minimum phase or Off and about 22 to 24 ms into linear phase at 44.1 and 48 kHz, about 18 and 19 ms at 96 kHz. If the IN trim was moved within the last 50 ms, the silence lasts until that move has finished (up to about 50 ms longer). In a test of such switches on every Ferrule product the largest sample-to-sample step on a 40 Hz tone read at most 1.086 times the signal's own (the line is 1.10). Content below 24 Hz inside the mute is not covered by that reading.
  • At 192 kHz with a 16-sample buffer the one buffer in which an oversampling-mode change swaps the oversampling chain takes longer than the buffer's period (a possible dropout at that moment on a host that cannot absorb it; the output is muted by the fade there). Measured on Ferrule Pre: Off to 8x linear 355 percent of the period, the worst other pair 341 percent, the smallest pairs 170 to 177 percent. The code is shared; the other products were not read on this.
  • The IN and OUT trims glide in dB over 50 ms, with no corner at either end: a move that is reversed halfway turns from where it is, and a move never passes its target. Moving IN and OUT in opposite directions at the same moment does not bump the level. In a test of single trim moves (60 Hz, 900 Hz and 8 kHz tones) the largest change of slope read at most 1.02 times the signal's own on every Ferrule product (the line is 1.10); a switch that changes the latency, made inside an IN move, adds no dip of its own.
  • Band gain and IN trim automated together. When a band gain and the IN trim are automated together in a ramp, the small level wobble during the move can differ with the host's buffer size (the plug-in reacts once per buffer, so a smaller buffer gives more, smaller steps). The largest difference is at most 0.75 dB, against up to 1.92 dB in a plain design in which the band gain and the IN trim glide separately, but a few individual cases differ more than in that plain design (the worst, a low-frequency band over a 100 ms ramp at 48 kHz, 0.60 dB against 0.04 dB).
  • Pressing EQ OUT during a band move. Pressing EQ OUT while a band move that the IN trim follows is still running (within a few tens of ms of the move) gives a brief level dip or swell that can be larger than in a plain design in which the band gain and the IN trim glide separately, by up to about 4 dB. That plain design also dips (about 5 to 6 dB) when EQ OUT is pressed early in such a move.
  • Host bypass and re-engaging. At minimum-phase oversampling (host rate below 150 kHz) the crossfades between the dry and the processed signal match the dry path's phase while blending. The price is a brief high-frequency dip: for this product its own reading was not taken. Linear phase, oversampling Off and rates of 150 kHz and up are not matched.
  • A parameter change made while the stereo mode is handing over is heard only from the end of the hand-over ramp (measured on Ferrule Pre: up to 110 to 119 ms at 48 kHz with 8x oversampling, 467 to 476 ms at 192 kHz; the code is shared, this product's own figures were not read).
Specifications

Formats & requirements

DeveloperGANUE Audio
Version1.0.0
WindowsWindows 10 or later (64-bit): VST3, AAX
macOSmacOS 11.0 or later: VST3, AU, AAX (one Universal build, Apple Silicon and Intel; signed and notarized)
StandaloneNone
LicenceOffline licence file, no iLok, no account, no online activation, no expiry
Trial14 days, full features
PriceUSD 19 until Nov 30, 2026, then USD 29USD 29. Also in the Ferrule Vintage Collection and the Ferrule Complete Collection
SHA-256, Windows installerb82422eea566ab18282bc82ff7ea94d13ea0c48aa21d70ca7447d66988b56c2e
SHA-256, macOS installer4d88c46ffac2f08b9f9b6799683341463b88210535c2079035feeb497fc77a7b
Buy · v1.0.0

Get Ferrule 81

USD 19 until Nov 30, 2026, then USD 29USD 29. Windows & macOS. 14-day full trial first.

Also in the Ferrule Vintage Collection (Ferrule Pre (free) with 66, 73, 81 and 84): USD 49 until Nov 30, 2026, then USD 69USD 69; and in the Ferrule Complete Collection (all ten plug-ins): USD 89 until Nov 30, 2026, then USD 119USD 119.

Checkout is handled by Gumroad. Your licence file and the installer links arrive in a separate email from [email protected]; drag the file onto the Ferrule 81 window and it unlocks, offline. The PDF manual is included. EULA

By continuing to checkout you agree to the EULA and the Refund Policy.